2024 Vermeer® Stump Cutters SC48TX

Information

2024 Vermeer® Stump Cutters SC48TX

Get in and out of sites efficiently with enough power to tackle the job.

The Vermeer SC48TX stump cutter delivers high efficiency from engine to the stump grinding wheel through a 48-hp diesel engine with a direct drive system. This machine gives operators access to tight and challenging jobsites with a narrow footprint and low ground pressure to complete a variety of jobs. Plus, operators can add features like the remote control and backfill blade to help increase productivity.

Features may include:

48-hp (36-kW) diesel engine
  • The 48-hp (36-kW) diesel engine provides optimal fuel economy, durability and performance to efficiently cut stumps of all sizes. Backed by proven worldwide service and support to maximize productivity.
Direct-drive system
  • This direct-drive system delivers the maximum amount of power to the cutter wheel and requires minimal maintenance.
Vermeer cutting system
  • Enhance jobsite productivity with the Vermeer cutting system – a two-sided cutter wheel that minimizes recirculation of material and maximizes cutting performance.
Retractable tracks
  • The retractable tracks allow operators to navigate the machine through narrow jobsite entrances.

Photos

Highlights

  • Glendon, Alberta
  • 2024
  • Vermeer®
  • Stump Cutters SC48TX
  • Control Station: Description Swing out | Operator Vision Shield Description: Abrasion-resistant coated polycarbonate
  • Ultra-low sulfur diesel
  • Available
  • (tracks retracted): 88.9 cm | (tracks extended): 124.5 cm
  • (non-remote unit): 193 cm | (remote unit): 215.9 cm

Specifications

  • 2024
  • Vermeer®
  • Stump Cutters
  • SC48TX
  • Stump
  • CAT
  • T4F/Stage V
  • C1.7
  • 3
  • Gross (Maximum): 35.8 kw
  • 166.8 Nm
  • Dry-type, restriction indicator, evacuator valve and safety element
  • Spin-on
  • Medium: Water/antifreeze
  • Max Fuel Consumption: 11 lph
  • Ultra-low sulfur diesel
  • Lower: Straight bevel
  • Electric clutch with brake
  • 2 universal joints | 2 standard with double lip seal
  • Spring-applied and hydraulically-released dual parking brakes
  • 950 CCA
  • System Voltage: 12 | Switches: Boom swing, boom height, creep propel, ignition, clutch, track gauge, track speed range and throttle, blade | Controller: Danfoss | Display: Multifunction display (MFD) that displays hours, fuel level, engine speed, engine faults and engine status | Shutdown System: High engine temperature and low oil pressure
  • 85A
  • Cutterwheel: 1235 rpm | High Travel: 2.4 km/h | Low travel: 1.8 km/h | Low Speed Travel: 30.5 m/min | High Speed Travel: 42.7 m/min
  • 107 dB(A)
  • System Type: Open loop
  • Pump Flow at Maximum RPM: 41.6 L/min | track: 11.4 gpm (43.1 L/min)
  • System relief: 199.9 bar | track: 2900 psi
  • Soft Ground: 39.2 kPa
  • Track Drive: Hydrostatic
  • Control Station: Description Swing out | Operator Vision Shield Description: Abrasion-resistant coated polycarbonate
  • Welded tube and plate steel
  • Warning Lights: Engine warning
  • Fan 16.5 in | Chip blade width (without extensions): 86.4 cm | Cutterwheel Cut Above Ground: 71.1 cm | Blade Travel Above Ground: 21.6 cm | Cutterwheel Thickness: 3.5 cm | Cutterwheel Diameter: 61 cm | Cutterwheel Cut Below Ground: 40.6 cm | Maximum Angle of Continuous Operation: 35 deg | Cutterwheel Straight Line: 165.1 cm | Chip Containment: .7 cu m
  • on Ground: 47 in (119.4 cm)
  • Rubber 7-in
  • 355.6 cm
  • (tracks retracted): 88.9 cm | (tracks extended): 124.5 cm
  • (non-remote unit): 193 cm | (remote unit): 215.9 cm
  • 54.9 L
  • Tank: 34.1 L
  • oolant Capacity (Engine and Radiator): 11 L
  • Oil Volume with Filter: 5 L | Lower Gearbox: 1.5 L
  • 1701 kg
  • Type of Idler: Cast | Tooth Description: Vermeer cutting system | Number of Teeth: 27 | Number of wear plates: 6 | Reversible Pockets/Teeth: 24
  • Recommended: 10W-30 | Oil Type - Lower Gearbox: SAE 75W90 synthetic gear oil | Recommended: Vermeer highpower 68