2024 Vermeer® Brush Chippers BC900XL

Information

2024 Vermeer® Brush Chippers BC900XL

?The Vermeer BC900XL brush chipper was designed to eliminate the guesswork out of chipping for smooth chipping performance.

Able to chip heavily branched material up to 9 in (22.9 cm) in diameter and 14 in (35.6 cm) wide, the BC900XL is ideal for line clearing and general cleanup needs. In combination, the Vermeer-exclusive SmartFeed system, and its 35 hp (26.1 kW) Briggs and Stratton gas engine, pulls in and processes difficult material.

Features may include:

SmartFeed system
  • Protect your engine with the SmartFeed system, which monitors engine speed and stops or reverses the feed rollers if needed.
Bottom feed stop bar
  • Provides operator safety with the patented bottom feed stop bar. The four-position upper feed control bar with dual stop positions and forward / reverse feed positions mounts over the feed table and enables the operator to stop the feed rollers and select forward or reverse operations.
1-year/1,000-hour limited warranty
  • Protect your investment with a 1-year/1,000-hour limited warranty.

Photos

Highlights

  • Glendon, Alberta
  • 2024
  • Vermeer®
  • Brush Chippers BC900XL
  • Tongue Description: 3" x 5" 3/16" (7.6 cm x 12.7 cm x .5 cm) Tube
  • Gasoline
  • Available
  • 201.9 cm | Infeed Table: 121.9 cm
  • 246.4 cm | Infeed Hopper: 81.3 cm | Chute: 245.6 cm

Specifications

  • 2024
  • Vermeer®
  • Brush Chippers
  • BC900XL
  • Brush
  • Briggs and Stratton Vanguard
  • Gross Horsepower (Maximum): 26.1 kw
  • 71.9 Nm
  • Engine-mounted
  • Spin-On
  • Medium: Air
  • 5.6 cm
  • 33.1 CID
  • Manufacturer: White
  • Max Fuel Consumption: 12.1 lph
  • Gasoline
  • Drive Engagement: Clutchless PTO
  • 3500 lb (1587.6 kg) / 3500 lb (1587.6 kg) with electric brakes | Type - Option: Rubber torsional | Manufacturer - Option: Dexter
  • ST215/75R14
  • 14" (35.6 cm)
  • Group 24 - 580 CCA
  • System: 12 V
  • 20 amp
  • Feed: 140 ft/min | 1500 rpm
  • Actuation Force (BFSB): 15.4 kg
  • System Type: Tandem Center
  • Pump Flow at Maximum RPM: 18.9 L/min
  • System relief: 172.4 bar | Auto Reverse PSI: 158.6 bar
  • 3925 cfm
  • Tongue Description: 3" x 5" 3/16" (7.6 cm x 12.7 cm x .5 cm) Tube
  • 3/16 in. x 5-5/8 in. (.5 cm x 14.3 cm)
  • Pintle or ball
  • Frame: .5 cm x 14.3 cm | Feed Roller Dimension: 15.8" dia x 13.5" long (40 cm x 34.3 cm) | Infeed Throat Capacity: 9 in x 14 in (22.9 cm x 35.6 cm) | Pinch Point - Distance to End of Feed Table: 165.1 cm | Distance from Feed Table to Ground: 73.7 cm | Infeed Table Material Thickness: .5 cm | Bottom Feed Stop Bar Diameter: 5.1 cm | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | Diameter: 5.1 cm | Material Thickness: .3 cm | Material Capacity: 22.9 cm | Thickness: 2.5 cm | Drum/Disc Diameter: 83.8 cm | Knife Thickness: 1.6 cm | Knife Size: 5" x 11.75" (12.7 cm x 29.8 cm) | Bedknife Size: 5" x 12.1" (12.7 cm x 30.7 cm) horizontal and 5" x 8.8" (12.7 cm x 22.4 cm) vertical | Bedknife Thickness: 1.9 cm | Bottom Thickness: .2 cm | Top Thickness: .3 cm | Side Wall Thickness:.3 cm | Deflector Thickness:.3 cm | Chute Rotation Angle: 270 deg
  • Feed Table Up, Tongue In: 356.6 cm | Table Down, Tongue Extended: 393.2 cmn | Infeed Table: 66 cm
  • 201.9 cm | Infeed Table: 121.9 cm
  • 246.4 cm | Infeed Hopper: 81.3 cm | Chute: 245.6 cm
  • 60.6 L
  • Oil Volume with Filter: 2.7 L
  • Feed Roller Clamp Load: 254 kg
  • 25.7 L
  • Feed Roller Orientation: Horizontal | Number of Feed Rollers: 1 | Feed Roller Clamp Type: Spring/weight | Number of Feed Roller Motors: 1 | Reset Method: Dual green hold-to-run buttons | Positions: Four positions: Emergency stop, forward, stop and reverse | Safety Lock - Number of Positions: 6 | Useable Edges: 2 | Fixture Method: Bolt-on | Bedknife - Number of Useable Edges: 2 | Number of Bearings: 2 | Rotation Type: Manual dual handles with pin lock | Filtration Method: 10 micron return | Fender Description: Bolt-on | Type: Dual spherical roller | Manufacturer: Linkbelt | Controller: Vermeer ACS
  • Of Feed Roller: 95.3 kg | With Shaft: 149.7 kg | Engine Option: 1388 kg | Tongue - Engine Option: 145.1 kg
  • Recommended: 10W30 | Vermeer VMF Gold
  • A8 chipper steel | Bedknife: Grade 50
  • Chipper - Polyester Cord with wrap
  • 12 / 2 | Number of Bolts/Knife: 5
  • 2